ULTRA FLEX 1000 - Polyurethane Elastomeric Coating
-
$0.00
Available Options
Videos and Instructions
FREQUENTLY ASKED QUESTIONS
Large Project? Get a Quote Here
UltraFlex1000 is a two-component, fast-setting, fast-curing, solvent-free, extremely flexible, high solids polyurethane elastomeric coating designed for interior and exterior concrete, plywood, and metal surfaces. It performs well in varied temperatures and humidity, with a rapid gel time suitable for applications down to 20°F (-6°C), and can be applied in single or multiple layers. It’s also ideal for filling expansion joints, providing flexibility and durability where movement is expected.
Recommended for high-traffic pedestrian and vehicular decks, as well as surfaces requiring durability and flexibility, such as walkways, patios, balconies, floors, and mechanical rooms.
Application Temperature
Temperature of 20°F (-6°C) and above. For best results, apply between 65°F to 80°F. Ask about our accelerate additive for colder temperatures.
Curing Temperature
At 75°F (24°C) and 50% relative humidity, allow each coat to cure for 2-4 hours before applying subsequent coats. Cure time will vary depending on temperature and humidity.
Cleanup
Clean equipment with an environmentally safe, polyurethane-grade solvent (alcohol-free) as permitted by local regulations, immediately after use.
Storage
UltraFlex1000 has a shelf life of 1 year from the date of manufacture in original, factory-sealed containers when stored indoors at temperatures between 60-95°F (15-35°C).
Surface Preparation
Speak with one of our experts for more information.
Mixing Instructions
Proportions are pre-measured. Using a mechanical mixer, pre-mix Part A and Part B separately until a uniform color is achieved, ensuring to scrape any solids from the bottom and sides of the pail. Slowly pour Part B into Part A while mixing, and scrape the sides of the container. Mix for 1-2 minutes, then box the materials. Continue mixing until color is uniform. Avoid mixing in an up-and-down motion.
Note: UltraFlex1000 must not be diluted.
Application Instructions
For best results, use a squeegee or notched trowel. A phenolic resin core roller may be used, but extra care should be taken not to trap air, as this may result in bubbles.
A continuous coating application is necessary to minimize lines and/or streaking.
To achieve a slip-resistant finish, apply an aggregate of washed, dry, rounded sand (approximately 16 or 20 mesh, 0.0331-0.0469 in.; 0.84-1.19 mm), with a minimum hardness of 6.5+ Mohs, at a rate of 20 lbs/100 sqft (1 kg/sqm) or as required. Broadcast sand into the wet second coat until refusal, covering it completely. Once the coating is dry, remove loose sand, preferably by vacuum.
For rubber granule applications, broadcast an aggregate of 14-30 mesh rubber granules into the membrane at a rate of 10 lbs/100 sqft (0.5 kg/sqm) or to refusal. When the coating starts to gel in approximately 20 to 30 minutes, broadcast 14-30 mesh (0.56-1.41 mm) rubber granules until refusal. When the coated surface is firm enough to support the weight of the installer without damaging the coating or once it is dry (approximately 4-6 hours), remove all loose aggregate, preferably by vacuum.
Warning
This product contains isocyanates and curative material.
Safety Gear
It is recommended to wear appropriate safety gear, including gloves, eye protection, and a respirator, to prevent exposure to chemicals and ensure safe application.
Important Note
If more than 48 hours passes between coats, re-prime the surface with a Spartan-approved primer before proceeding.
Limitations
This product is not UV stable. The following conditions should not be coated with Spartan Epoxies deck coatings or systems: split slabs, buried membranes, sandwich slabs with insulation, slabs over unvented metal pans, magnesite, and non-structural lightweight concrete. On-grade slabs may receive Spartan Epoxies system coatings if a moisture-vapor transmission test is performed first. Contact Spartan Epoxies technical department with test results.
For coating asphalt surfaces, please contact the Spartan Epoxies technical department. Surfaces must be dry, clean, and free of foreign matter. Clear coatings may turn opaque and cloudy due to moisture penetration, especially in exterior applications. Surfaces may become slippery when wet. Opened containers must be used as soon as possible. Do not dilute under any circumstance.
Technical Support
For application support, contact your Spartan Epoxies Sales Representative at 1-877-288-1952, email spartanepoxies@gmail.com, or start an online chat at www.spartanepoxies.com.