Black Friday Sale + Spend $500 or more get FREE SHIPPING! Ends 12/03/24! Call or chat today! Large Project? Request a Quote.
  • SPE- PS95 - Polyaspartic Sealer / Binder

SPE- PS95 - Polyaspartic Sealer / Binder

High Performance Polyaspartic Sealer / Binder / 80 – 160 square feet per gallon at 16 to 8 mils. 95% Solids (Clear) Polyaspartic. Can be used as binder for a metallic epoxy system, or a seal coat. Recommended when a fast cure time, extra heat and a ...
  • $0.00

Available Options

High Performance Polyaspartic Sealer / Binder / 80 – 160 square feet per gallon at 16 to 8 mils. 95% Solids (Clear) Polyaspartic. Can be used as binder for a metallic epoxy system, or a seal coat. Recommended when a fast cure time, extra heat and abrasion resistance is needed. 


CURE SCHEDULE:  (70°F) (70% relative humidity)

Pot life (to gel) – (150 gram mass)….….….…....Greater than 2 hours

(Actual usable working time is approximately 30 minutes,
depending on environmental conditions and volumes).


Tack free (dry to touch)………………………………………3-4 hours

Recoat or top oat .....……..…………………………….......... 3-5 hours

Light Foot Traffic / Light Use ………………......................…3-5 hours

Full cure (heavy traffic) ……..………..………..………..... 24-48 hours 


APPLICATION TEMPERATURE:

50-90 degrees F with relative humidity below 85%


PRODUCT DESCRIPTION: PS95 is a two component 95% solids polyaspartic aliphatic polyaspartic sealer.  This material can be used as the base coat and the topcoat over paint chip decorative broadcasts or colored sand broadcasts to provide an infinite array of color schemes or patterns.. PS95 has excellent chemical resistance, hardness, abrasion resistance, UV stability and has an excellent clear gardner color.  However, the outstanding feature of this product is its quick tack free time for foot traffic.


RECOMMENDED FOR:

Recommended for areas where a medium build broadcasted floor / surface is desired and installation downtime is very limited.  This material can also be applied over a broadcasted or troweled system as a thin to medium build sealer.


SOLIDS BY WEIGHT: 95% (+/- 1%)

SOLIDS BY VOLUME: 94% (+/-1%)

VOLATILE ORGANIC CONTENT: Less than 50 grams per liter

COLORS AVAILABLE: Clear – gardner color 1-2

RECOMMENDED FILM THICKNESS:

.10-15 mils. (when applying directly to concrete, precautions should be taken to properly prepare the substrate and the moisture content of the substrate should be tested. Do not apply to damp surfaces.) COVERAGE PER GALLON: 107 – 160 square feet per gallon 

PACKAGING INFORMATION:

2.5 gallon kit (other special kit sizes are available upon request.(packaging information is approximate net volume)

MIX RATIO: 12.95 pounds part A to 9.3 pounds part B. The mix ratio is approximately 1.5 gallons part A to 1 gallon part B.

SHELF LIFE: 6 months in unopened containers

FINISH CHARACTERISTICS: Gloss (>70 at 60 degrees @ glossmeter)

COMPRESSIVE STRENGTH: 11,500 psi @ ASTM D695

TENSILE STRENGTH: 3,800 psi @ ASTM D638

ULTIMATE ELONGATION: 2.4%

HARDNESS: Shore D= 75

ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles= 20 mg loss

ADHESION: 340 psi @ elcometer (concrete failure, no delamination, applied to shotblasted concrete)

VISCOSITY: Mixed= 1,000-2,000 cps (typical)

DOT CLASSIFICATIONS: Part A “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III 

Part B “UN1993, FLAMMABLE LIQUID N.O.S. (CONTAINS Xylene), 3, PG III  


CURE SCHEDULE:  (70°F) (70% relative humidity)

Pot life (to gel) – (150 gram mass)….….….…....Greater than 2 hours

(Actual usable working time is approximately 30 minutes,
depending on environmental conditions and volumes).


Tack free (dry to touch)………………………………………3-4 hours

Recoat or top oat .....……..…………………………….......... 3-5 hours

Light Foot Traffic / Light Use ………………......................…3-5 hours

Full cure (heavy traffic) ……..………..………..………..... 24-48 hours 


APPLICATION TEMPERATURE:

50-90 degrees F with relative humidity below 85%

 

 

CHEMICAL RESISTANCE:

REAGENT                 RATING

xylene C

1,1,1 trichloroethane B

MEK A

methanol B

ethyl alcohol B

skydrol C

50% sodium hydroxide E

10% sulfuric acid C

10% HC1 (aq) C

5% acetic acid C


Rating key:
A - not recommended B - 2 hour term splash spill
C - 8 hour term splash spill D - 72 hour immersion
E - long term immersion.

NOTE: extensive chemical resistance information is available through your sales representative.


PRIMER: Recommend a suitable epoxy broadcasted base system and/or adhesion testing prior to use.


TOPCOAT: Optional: none required

LIMITATIONS:

*Color stability may be affected by environmental conditions like high humidity/chemical exposure.  Exposure to some types of lighting such as sodium vapor lights may cause discolorations.

*Clarity of color may vary from batch to batch.

*Substrate temperature must be 5°F above dew point.

*Too thick of an application may result in surface imperfections or bubble generation.

*Always apply a test patch to determine product suitability and adhesion performance for your proposed application method and procedures.

*All new concrete must be cured for at least 30 days prior to application.

*Do not expose this product to water until fully cured.

*See reverse side for application instructions.

*Physical properties are typical values and not specifications.

*See reverse side for limitations of our liability and warranty.

*Relative humidity can affect dry time and gel time – See page 2

  • 0%
  • 0%
  • 0%
  • 0%
  • 0%

Reviews Over SPE- PS95 - Polyaspartic Sealer / Binder

Total Reviews (0)
click here write review to add review for this product.