ACCEL100- 1.5 Gallon Kit
-
$185.32
- $218.02
Customise your product
Videos and Instructions
FREQUENTLY ASKED QUESTIONS
Large Project? Get a Quote Here
ACCEL100 1.5 Gallon Kit will cover 199.5 sq ft @ 12 mils. ACCEL100 is a two component 93% solids colored epoxy coating designed for applications where a high solids primer is needed before applying high solids or 100% solids topcoats for build coats over concrete. ACCEL100 has good low temperature cure capabilities down to as low as 45°F. However, ACCEL100 only has fair color stability and should be top coated with an aliphatic urethane when long term color stability is a requirement.
Recommended for Recommended for a high build basecoat on concrete or masonry. Product is suitable in many chemical exposure environments..
Packaging Information: 1 Gallon Part A and a 1/2 Gallon Part B.
Cure Schedule
Pot life – 150 gram mass …….……….…………...26-38 minutes
tack free (dry to touch)…………...…………...……...…..4.5- 6.0 hours
recoat or topcoat.....……………...…........................................ 7-9 hours
light foot traffic...………………………………......………..8-12 hours
full cure (heavy traffic)... ……………..…………...…...….......2-5 days
This 1.5 Gallon kit will cover:
199.5 sq ft @ 12 mils
400 @ 6 mils
Per Gallon:
133-267 sq ft/gal @ 6-12 mils
Cure Schedule: 70 degrees:
Pot Life - 1.5 gallon volume: 35 to 55 mins
Tack Free (dry to touch): 6 to 9 hours
Recoat / Topcoat: 10 to 14 hours
Light Foot Traffic: 12 to 16 hours
Full Cure: 2 to 7 days
Application Temperature:
45 - 90 Degrees F with relative humidity below 85% for best results.
SOLIDS BY WEIGHT: 100% (+/- 1%)
SOLIDS BY VOLUME: 100% (+/- 1%)
VOLATILE ORGANIC CONTENT: Less than 2 g/l
STANDARD COLORS: Light Gray, Medium Gray, Tile Red, & Beige
RECOMMENDED FILM THICKNESS: 12-30 mils
COVERAGE PER GALLON: 53-130 FT2 per gallon @ 12-30 mils
PACKAGING INFORMATION:
3 gallon kit (2.9-3.0 gallons net approximately)
15 gallon kits (14-15 gallons net approximately)
MIX RATIO:
12 pounds (1 gallon) Part A to 4.05 pounds (.50 gallons) Part B (volumes approx.) (standard colors)
SHELF LIFE: 1 year in unopened containers
FLEXURAL STRENGTH: 7,400 psi @ ASTM D790
COMPRESSIVE STRENGTH: 10,000 psi @ ASTM D695
TENSILE STRENGTH: 5,800 psi @ ASTM D638
ADHESION: 440 psi @ elcometer (concrete failure, no delamination)
ULTIMATE ELONGATION: 3.2%
FINISH CHARACTERISTICS: Gloss (>70 at 60 @ glossmeter)
HARDNESS: Shore D= 70
GARDNER VARIABLE IMPACTOR: 50 inch lbs direct – passed
ABRASION RESISTANCE:
Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles= 26 mg loss
VISCOSITY: Mixed = 1000-2000 cps (typical, most colors)
DOT CLASSIFICATIONS:
Part A not regulated
Part B “CORROSIVE LIQUID N.O.S., 8, UN1760, PGIII”
PRIMER: HDWB, HDPRO, ACCEL93, any of our suitable primer.
TOPCOAT: Optional: Pigmented versions of HPU, TC92, or any of our non-yellowing aliphatic urethanes can be used for increased chemical resistance or increased UV stability. Talk to a Spartan Epoxies Expert for further solutions / options.
Tags: Fastset Epoxy Primer